Beulah Mine — Accidents
Total: 70 accidents | Fatalities: 0
| Date | Classification | Injury | Days Lost | Narrative |
|---|---|---|---|---|
| 02/11/2026 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was sweeping in truck shop. The broom handle broke and pinched finger resulting in 2 stitches |
| 07/02/2024 | MACHINERY | DAYS AWAY FROM WORK ONLY | 22d lost | While being loaded in an End Dump with dirt, the operator experienced bouncing in the cab when the excavator dropped a bucket load into the truck. The operator reported experiencing soreness in the ne... |
| 06/28/2023 | SLIP OR FALL OF PERSON | NO DYS AWY FRM WRK,NO RSTR ACT | None | The employee was fueling a water pump. The employee slipped in the mud and rolled left ankle causing a sprain. The employee continued to work. On 7/17/23 the employee received medical treatment for... |
| 11/02/2022 | HANDLING OF MATERIALS | DYS AWY FRM WRK & RESTRCTD ACT | 5d lost, 7d restricted | The injured employee was removing a jack stand from under a D6 dozer. EE pulled the pin to collapse the extension and it did not collapse. When it did collapse, EE's finger was pinched, causing an a... |
| 10/08/2020 | SLIP OR FALL OF PERSON | NO DYS AWY FRM WRK,NO RSTR ACT | None | A contractor was dismantling a building that the contractor purchased at auction. Contractor hired two temp workers to help. One of the temp workers fell approximately 20 ft and was injured. |
| 12/04/2017 | SLIP OR FALL OF PERSON | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee had taken a shower at the end of EE's shift. EE was walking from the shower to EE's locker when EE slipped. EE's right hand caught a sharp edge of a locker when EE fell. EE's right hand pa... |
| 09/27/2016 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee was struck by a piece of metal while operating a truck mounted hoist about 20 feet away from another employee that was using a hammer tapping a metal dragline bucket shroud. A piece of metal... |
| 02/17/2016 | MACHINERY | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was removing cutting edges from a Cat 966 loader bucket. The bolt had a flat edge & when the nut was loosen the head (underside of bucket) of the bolt dropped & spun around lacerating EE's finger.... |
| 12/23/2015 | SLIP OR FALL OF PERSON | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was walking out of the maintenance shop in the dark & fell on a patch of ice covered from overnight snow. EE landed on EE's left side & arm. EE declined medical attention at the time. EE had a doc... |
| 12/16/2015 | MACHINERY | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was using a grinder to cut out an unused metal chute in the tipple. The grinder got caught & kicked back striking EE in the right leg above the knee cap. Seven (7) stitches were needed to close t... |
| 07/22/2015 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 28d lost | EE found lying on the ground by a D11 dozer. EE alleges he was about to climb onto the dozer slipped & fell. EE does not know what happen. EE is a large person & was complaining of severe headache, di... |
| 03/11/2015 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 110d lost | EE stepped off of a raise platform(8"" high)to the floor of the 1570's house. When EE stepped off the raised area EE heard a pop in the L knee. Knee x-rayed, inconclusive. EE returned to work on restr... |
| 11/26/2014 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 14d lost | Cleaning Service lady was taking garbage to a dumpster when she slipped & fell backwards hitting her head on the ground. She had walked to the wrong dumpster - a little used scrap metal dumpster not... |
| 08/14/2014 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was turning a large spare point sheave for a BE 1570 dragline. Point sheave was mounted on a storage rack. It is recommended that the sheave be rotated from time to time to prevent the sheave fro... |
| 08/07/2014 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 20d lost | Employee was pulling a suction hose and float from a pond when the employee slipped on a muddy area, fell and twisted his lower back |
| 06/17/2014 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employees was doing routine crack repair and at some point got metal debris in his left eye. Unknown when the debris actually entered the eye. |
| 06/11/2014 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 88d lost | Employee was removing a belly pan from a d-11 dozer. a bolt used to lift with broke causing the belly pan to wedge employee's right ankle between the belly pan & the framework of the ripper |
| 01/09/2014 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 10d lost | Employee had finished assisting with the replacement of brake shoes on the 1570 dragline. As employee was leaving the area, employee felt a pop in his lower back. Employee was examined by the local... |
| 05/20/2013 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 72d lost | EE was changing a filter on a rubber tire dozer in the grease shop. EE was extending his arm to loosen the filter. EE felt a pop in his right arm near the elbow. Medical examination was diagnosed a... |
| 05/16/2013 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was preparing to change shanks on a reclamation chisel plow. Bolts were covered with dirt. EE used gloved hand to remove dirt. EE felt a sharp pain on his left thumb. A sharp edge on the bolt head... |
| 03/05/2013 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 17d lost | Maintenance EE mounting a scraper at the rear engine to check engine. EE missed a step causing EE to lose balance & fall. EE landed on right wrist which was fractured. |
| 01/17/2013 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE removed & cut a door spring with a torch. EE was using a chisel & hammer to remove slag to free the spring. Injured EE was standing behind the EE when a sliver of slag flew off striking the injured... |
| 01/10/2012 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee banged his hand between the wire rope cable & cable hook as he was fastening the hook to a rail car. Employee's RT 4th finger was still swollen on 01/11/2012. X-ray's revealed a fracture bet... |
| 10/12/2011 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 11d lost | Employees were assigned to assist in making a 6x6 truck operational. Employee was walking around the disabled truck when he tripped on a rut & fell. Employee was examined at the local hospital where a... |
| 04/05/2011 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employees were using a port-a-power to hold steering tire at full turn position. Employee's did not have the proper length of ram so they were using a block to make up the difference. Ram snapped out... |
| 01/30/2011 | SLIP OR FALL OF PERSON | INJURIES INVOLVNG NONEMPLOYEES | None | Security Officer doing foot patrol and slipped on ice, falling backwards and landed on left wrist, breaking it. |
| 06/12/2010 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | Gear was being lowered in the revolving frame to be installed by a crane. Gear was hanging approximately one inch off the floor and slowly rotating on it's own. Employees finger was pinched between g... |
| 06/10/2010 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | Removing lower second gear on propel dragline gear that was stuck, the gear came free force, caused by realease of pressure on the gear and it created a pinch point. |
| 08/14/2009 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee (temporary welder) was removing wear plates from an old dragline bucket when a metal splinter flew off striking employee in the right index finger. Employee was using a 20 pound hammer to hi... |
| 08/14/2009 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | Welder removing wear plates from an old dragline bucket when a metal splinter flew off striking the welder in the right thigh. Employee was using a 20 pound hammer to hit the wear plate. Employee ta... |
| 03/04/2009 | POWERED HAULAGE | DAYS AWAY FROM WORK ONLY | 1d lost | A mechanic was operating the shop overhead crane placing a planetary gear on a haul truck. While attempting to lift a tool to be attached to the gears the employee activited the high speed lift butto... |
| 11/04/2008 | HANDTOOLS (NONPOWERED) | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee was removing spacer plates from horizontal fairlead sheave. He was helping a welder break the bead off the plates. As he turned a plate the welder swung a hammer striking the employee on his... |
| 08/20/2008 | SLIP OR FALL OF PERSON | NO DYS AWY FRM WRK,NO RSTR ACT | None | Employee was climbing down off his Caterpillar track dozer, when he slipped and fell. Employee alleges he kept hold of the handhold but hit his lower back on the dozer's arm. Employee refused treatm... |
| 04/23/2008 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was removing a bolt from a reclamation chisel plow.EE put hand on the top of bolt to hold it down, then used a air wrench to remove bolt.When the air wrench spun the bolt a sharp edge cut the left... |
| 04/12/2008 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE had completed fueling his dozer. EE was attempting to reel the fuel hose back on the reel. It was dark so the EE was trying to feel the button. He reached passed the reel start button, when his arm... |
| 01/22/2008 | OTHER | DAYS AWAY FROM WORK ONLY | 14d lost | Employee was on a break sitting on a work bench. Another employee pulled on the employee's legs causing the the employee to slide to the edge of the work bench. The employee reached down with her hand... |
| 10/25/2007 | FIRE | ACCIDENT ONLY | None | A BN train delivering limestone to the Coyote Station power plant started 4 spot fires along the railroad tracks. One spot fire was determined to be on the mine permitted area. This fire burned native... |
| 10/09/2007 | DISORDERS (REPEATED TRAUMA) | OCCUPATNAL ILLNESS NOT DEG 1-6 | 54d lost | Employee reported to Dakota Westmoreland that he had been seen by a physician on Oct. 9, 2007 because he alleges that he was experiencing numbness in his left hand. |
| 08/21/2007 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 27d lost | Employee was lifting a sheet of iron using a hook. The hook came loose from the sheet of iron. The sheet of iron struck his left wrist. |
| 06/21/2006 | MACHINERY | DAYS AWAY FROM WORK ONLY | 64d lost | Employees were removing a bull gear from the house of a BE480 walking dragline. Employees were using an overhead crane to manuever the gear out of a side door. The gear was attached to the overhead... |
| 09/11/2005 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE WAS SETTING A TRAILER-MOUNTED WATER PUMP IN A WATER HOLE IN THE ""C"" PIT. THE WATER PUMP OVER BALANCED TO THE HITCH & THE STABILIZING DROP JACK FELL OUT OF THE FRAME. USING HIS BODY WEIGHT, EE R... |
| 02/22/2005 | HANDLING OF MATERIALS | NO DYS AWY FRM WRK,NO RSTR ACT | None | EE was moving a 55 gallon drum of coal from the bed of a pickup to the bucket of a front end loader. the barrel fell toward the ee and twisted ee anke. medical treatment was sought and ee was examined... |
| 10/08/2004 | HANDTOOLS (NONPOWERED) | DAYS AWAY FROM WORK ONLY | 170d lost | EMPLOYEE WAS INSTALLING A HYDRAULIC CYLINDER ON A CAT SCRAPER IN OUR MAINTENANCE SHOP. HE ALLEGES THAT A PRY BAR HE WAS USING TO INSTALL THE CYLINDER SLIPPED CAUSING A STRAIN ON HIS LEFT SHOULDER. THE... |
| 08/11/2004 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 17d lost | Employee had been working in the lower area of the BE1570 dragline. After climbing out of this area employee alleges he stepped on the edge of a manhole cover rolling & twisting his ankle. |
| 05/09/2004 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 10d lost | EMPLOYEE ALLEGES THAT WHILE SHUTTING THE DOOR TO THE OPERATORS CAB OF THE DRAGLINE, EE CAUGHT HIS FINGER BETWEEN THE DOOR & THE DOOR JAM FRAME. EE'S FINGER WAS CRUSHED & THE END (TIP) OF THE FINGER SE... |
| 02/24/2004 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 10d lost | EE WAS POWER WASHING SCRAPER WHEN HE RECIEVED 1ST & 2ND DEGREE BURNS TO THE TOP OF HIS LEFT FOOT. WHILE WASHING THE GOOSENECK, THE HOSE GOT HUNG-UP, EE PULLED ON THE HOSE IN DOING SO, THE TIP OF THE W... |
| 01/05/2004 | POWERED HAULAGE | DAYS AWAY FROM WORK ONLY | 7d lost | EE WAS OPERATING A CAT 651 SCRAPER, WHEN HE ALLEGES THE REAR OF THE SCAPER STARTED SLIDING SIDEWAYS DOWN THE SLOPE HE WAS WORKING ON. THE TOP OF THE SLOPE OF THE PIT AREA WAS ICY CAUSING THE S CRAPER... |
| 06/27/2003 | SLIP OR FALL OF PERSON | DAYS AWAY FROM WORK ONLY | 5d lost | WHILE WALKING TOWARDS AN EMPLOYEE TO ASK A QUESTION, THE EMPLOYEE SLIPPED & FELL TO THE GROUND, SPRAINING HIS RIGHT ANKLE. THE ACCIDENT WAS NEAR A WATER TRUCK FILLING AREA. THE GROUND WAS WET, LOOSE S... |
| 02/28/2003 | HANDTOOLS (NONPOWERED) | DAYS AWAY FROM WORK ONLY | 10d lost | EE ALLEDGES THAT WHILE INSTALLING A CYLINDER ON A LOADER, HE WAS HITTING A PIN WITH A SLEDGEHAMMER WHILE IN AN AWKWARD POSITION CAUSING HIM TO STRAIN HIS LOWER BACK. EE DID NOT INDICATE TO THE MINE TH... |
| 03/21/2002 | HANDLING OF MATERIALS | DAYS AWAY FROM WORK ONLY | 14d lost | EE ALLEGES THAT HE & A WITNESS WERE PUTTING A MAIN BEARING CAP BACK ON A CATERPILLAR D-11 DOZER. EE ALLEGES THAT THEY TRIED TO LIFT THE BEARING BY HAND, BUT IT WAS TOO HEAVY TO HOLD, WHILE TRY ING TO... |