SHM 27 Highwall Miner — Accidents

Total: 17 accidents | Fatalities: 0

Date Classification Injury Days Lost Narrative
04/09/2025 SLIP OR FALL OF PERSON DAYS AWAY FROM WORK ONLY 113d lost After trouble shooting a fault issue, crew exited base frame of the highwall miner utilizing the right rear ladder below the BPM. Injured was the last one down, as they stepped to the ground right ank...
11/06/2024 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None EE was repairing the conveyor roller head. EE was using a pry bar to roll the head over, the pry bar dislodged causing EE to fall and strike EE's left thumb on the conveyor guard. EE received 7 suture...
01/28/2016 HANDLING OF MATERIALS DAYS AWAY FROM WORK ONLY 267d lost Mine is IDLE: Superintendent was lifting crib blocks to stage up highwall miner to remove from job site when employee strained employee's lower back.
10/29/2015 HANDLING OF MATERIALS DAYS AWAY FROM WORK ONLY 265d lost On 11/3/2015 EE reported to Supervisor, that appx a week ago he hurt his right shoulder while removing a pin from the steering jack on the highwall miner with a slate bar. He didn't think he was hurt...
10/28/2015 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None Employee reported to Supervisor on 11/4/2015 that he had hit his shin with a 20lb. sledge hammer while securing locking pins in push beams of highwall miner.
11/09/2011 HANDLING OF MATERIALS NO DYS AWY FRM WRK,NO RSTR ACT None Employee was pulling a pin from the cutter chain, using a chain hoist. The hook on the end of the chain hoist broke, flew and struck employee's left wrist, causing a fracture.
06/12/2011 HANDLING OF MATERIALS NO DYS AWY FRM WRK,NO RSTR ACT None Employee was using a torch to cut steel plate. When he removed the piece and set it down, it shifted and struck his left forearm, causing a 2nd degree burn.
04/08/2011 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None Employee was striking the cog on the tailpiece with a hammer when a piece of the cog broke off, striking employee in the left forearm, resulting in a piece of metal embedded in the forearm, not remove...
12/27/2010 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None Employee was loosening a bolt on the highwall miner when his wrench slipped, striking him in the mouth. This resulted in chipping one tooth and breaking another tooth. The broken tooth required extrac...
10/19/2009 FALL OF FACE/RIB/PILLAR/SIDE/HIGHWALL ACCIDENT ONLY None Highwall failure measuring 40'(H) x 5'(T) x 30'(W).
07/25/2009 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None Employee was attempting to hit a punch with a 3# sledge hammer, in order to repair the handle on another sledge hammer by driving out the wedge. Employee missed the punch & struck his left hand.
05/16/2009 MACHINERY DAYS AWAY FROM WORK ONLY 4d lost Employee was drilling an anchor hole with hand-held auger. The auger was bent and caused the employee's hand to be caught between drill and anchor pin, injuring his left middle finger.
08/03/2008 HANDTOOLS (NONPOWERED) DAYS RESTRICTED ACTIVITY ONLY 1d restricted While tightening the cutter chain on the highwall miner, EE was struck by a piece of metal that broke off a hammer that was being used.
01/14/2008 HANDLING OF MATERIALS DAYS AWAY FROM WORK ONLY 50d lost While guiding a pin into the hole with his knee, the employee felt his knee pop and pain shot down his leg.
07/06/2006 HANDTOOLS (NONPOWERED) NO DYS AWY FRM WRK,NO RSTR ACT None Employee was striking latch pins when a piece of metal came off of pins & struck his leg (R). THIS WAS NOT A LOST TIME ACCIDENT!!!
12/22/2004 FALL OF FACE/RIB/PILLAR/SIDE/HIGHWALL DAYS AWAY FROM WORK ONLY 119d lost While working on the highwall miner, employee was struck in the back by a rock that fell from the highwall. He then struck his his knee on the cutter head.
12/14/2004 HANDLING OF MATERIALS DAYS AWAY FROM WORK ONLY 1d lost Employee injured his finger when a miner head that he was working on slipped & caught his finger between the plate & miner head.